Solid State Guitar Amp Forum | DIY Guitar Amplifiers

Please login or register.

Login with username, password and session length
Advanced search  

News:

SSGuitar has been upgraded to SMF v2.0.15!

collapse
Pages: [1]   Go Down

Author Topic: Help with TDA2003 amp, a big project.  (Read 365 times)

Victor Van Dort

  • Chipper
  • *
  • Chip Points: 0
  • Posts: 2
    • View Profile
Help with TDA2003 amp, a big project.
« on: November 03, 2017, 04:18:29 AM »

Hello guys, my first post here.
I want to realize a big little amp for practice for my electric guitars.
After some mini amp I would like to build something louder. I found this mini amp:
http://www.hotoneaudio.com/products/nanolegacy/Amplifier1/2016/1114/183.html


None schematic, but I know it based on TDA2003. I already built a Triple Wreck to use as hi-gain channel, but also a Tonemender to use as clean channel. I like both when I tested them with the guitar and my main guitar amp.

Now I built the TDA2003 power amp taken from the last part of this schematic:
http://www.redcircuits.com/Page145.htm

Of course, I have omitted the input stage.

But, testing the TDA2003 circuit I have many problems. I partially shielded with tinfoil.
I connected the circuit with a cheap homemade cab with a guitar speaker 8", 8 Ohm, 15w.
The PSU is a 12v 3A.

1. Too much hum when I increase the volume.
2. Some ground problem, I guess, I feel through my fingers a kind of... tingle? when I touch the hardware of the guitar as well as the strings.
3. I wanted a clean amp, but this start to clip too soon. At max I got about the distortiom of a LM386, and not more volume then my Noisy Cricket (LM386 based).

Need help.

Thank you!
Logged

Loudthud

  • Elite SSGuitarist
  • *****
  • Chip Points: 29
  • Posts: 181
    • View Profile
Re: Help with TDA2003 amp, a big project.
« Reply #1 on: November 04, 2017, 12:39:00 AM »

No amount of shielding will fix a noisy power supply. Try running the amp from a 12 Volt battery. Next, measure the Voltage to ground from each IC pin and post the results here.
Logged

Victor Van Dort

  • Chipper
  • *
  • Chip Points: 0
  • Posts: 2
    • View Profile
Re: Help with TDA2003 amp, a big project.
« Reply #2 on: November 04, 2017, 04:02:14 AM »

I don't have 12v battery. Can I use a 9v as well? At least about the noise.

Update: Tried the 9v battery. No noise, just a bit of hum, but it still oscillate when the pot is over the half and when the volume guitar pot is to zero. Because the flying connections of the clips and wires I didn't shielded it with the tinfoil this time.

Tried to put in front of it a Fetzer Valve or a Woody Acoustic Simulator. No changing about oscillating. It still too much distorted at half volume.
« Last Edit: November 04, 2017, 05:25:15 AM by Victor Van Dort »
Logged

blackcorvo

  • Master SSGuitarist
  • ****
  • Chip Points: 4
  • Posts: 90
    • View Profile
    • My Youtube Page
Re: Help with TDA2003 amp, a big project.
« Reply #3 on: December 01, 2017, 09:29:42 AM »

A 9v battery doesn't have enough capacity to power that amplifier, that's why it oscillated.

What you need is to connect the "negative" wire from the power supply to ground. Your power supply either uses one of those 2-prong outlet plugs, or the negative isn't grounded, to keep the 12v "floating" (aka isolated from ground references), which isn't something you really want for audio.

Either get a proper 12v 7Ah sealed battery for your tests, or find a way to ground the negative of your power supply.
Logged

Katoda

  • SSGuitar Regular
  • ***
  • Chip Points: 2
  • Posts: 11
    • View Profile
Re: Help with TDA2003 amp, a big project.
« Reply #4 on: December 03, 2017, 01:26:45 PM »

At 9V, the chip would have less than 2W of output with an 8 ohm speaker (isn't even on the datasheet), so it really cannot be than much louder than a LM386 based design. Also, the input sensitivity is in the 100mV range and your preamp probably delivers much more, so these two things explain the output and the distortion. Oscillations might then also be coming from long flying leads and high gain.
Logged
Pages: [1]   Go Up
 

* User Controls
 
 
Welcome, Guest. Please login or register.
Did you miss your activation email?
* Recent Posts
Peavey Studio pro 40 has squeel by mikeskory
[Today at 11:25:05 AM]


Heatsinks for your poweramp by Jazz P Bass
[Today at 10:45:07 AM]


New here - JC-120 #492020 - chasing down info by DrGonz78
[December 10, 2017, 02:12:27 PM]


Motor boating..but not the fun kind by dogbox
[December 09, 2017, 03:57:37 PM]


Help with TDA2003 amp, a big project. by Katoda
[December 03, 2017, 01:26:45 PM]

* Sponsors