Solid State Guitar Amp Forum | DIY Guitar Amplifiers

Please login or register.

Login with username, password and session length
Advanced search  

News:

SSGuitar has been upgraded to SMF v2.0.14 and PHP7!

collapse
Pages: [1]   Go Down

Author Topic: EBay TDA2050 boards  (Read 157 times)

tpb03

  • SSGuitar Apprentice
  • **
  • Chip Points: 0
  • Posts: 7
    • View Profile
EBay TDA2050 boards
« on: September 12, 2017, 08:52:34 PM »

A few years ago I started to make a small combo amp for practicing in my bedroom. Due to starting a family I ran out of time and abandoned the project, but not before building a nice pine cab based upon the Fender 5F1 combo.

I now want to complete the project as a 5W SS Champ style amp. I have ordered one of these cheap TDA2050 boards form ebay http://www.ebay.com.au/itm/DC-12-24V-5W-120W-TDA2050-Mono-Channel-Audio-Power-Amplifier-Board-Module-kit-/142443279688 which from the TDA2050 datasheet will deliver about 5W into an 8 Ohm speaker  at 18V single supply (I have some old 18V 4A laptop power supplies). I don't really trust the claims of 12-24V 5W- 120W, but happy to be shown wrong!

Could this project be as simple as (input -> Fetzer valve -> TDA board -> speaker) or do I need to put a buffer in somewhere? Also when running a fetzer vale at 18V, do I bias the transistor at 9V? (I obviously need to do some homework).

Does anyone have any experience using these prefab boards?

Tim
Logged

J M Fahey

  • SSGuitar Global Mod
  • Legendary
  • ****
  • Chip Points: 422
  • Posts: 4086
    • View Profile
Re: EBay TDA2050 boards
« Reply #1 on: September 15, 2017, 08:35:42 PM »

Seller claims are wild unbelievable, from 120W out (out of a max. +24Vdc supply) :loco  to being able to be powered from USB (lower voltage than minimum acceptable) to being powered from AC (IŽd LOVE to see that).
That said, it *should* work like a plain TDA2050 single supply datasheet example, so "just trust the datashet, not the seller".

Post here the preamp schematic you want to use with it.

If powered from 9V, you can easily get them from your +18V supply, all it takes is a resistor, a 9V Zener and a 100uF x 25V cap.

Nice project, now you must hunt for a suitable speaker.

Link to some Aussie site selling speakers to help you choose one.

Basically light, thin paper cone, like those cheesy 6 x 9 speakers old Falcons used to carry as factory installed ones in the 70s; you do NOT want "woofer" anything which will be dull and inefficient with guitar.

Or hunt pawnshops or Aunt EdnaŽs attic for old "home console" speakers, killer sound with guitar.
Logged

tpb03

  • SSGuitar Apprentice
  • **
  • Chip Points: 0
  • Posts: 7
    • View Profile
Re: EBay TDA2050 boards
« Reply #2 on: September 17, 2017, 08:22:52 PM »

Thanks J M.

I will treat it as per the datasheet single supply. I also have a TDA2030 board that is claimed 15W 6-12V single supply. As I have the TDA2030 board already, I will test it at 12V and then higher just playing music from my phone.

I have been searching for a preamp and found this schematic on the forum (post https://www.ssguitar.com/index.php?topic=1778.15).

It is Runoffgroove's Fetzer Valve with a buffer. This should give me a good approximation of the Champ tone going into the power amp board. Its also setup for 18V, although I did have a look through my laptop supply collection and the nearest is 19V. I'll test them all with my multi-meter to work out true voltages as from experience laptop supplies and wall-worts can be +/- 2V either way.

I would like to modify the preamp for two inputs like the 5F1. I'll report back when I proto this, but I think I will need to change the 4.7K input resister to 2 resisters running in parallel like the champ input. I can then solder the 1 Meg resister from active to ground on the input jack rather than on the board.



As for speakers, I have an 8" 8 Ohm guitar speaker from an old Park G10.

I'll report back here to share my experience as I am bound to need to help along the way!

Tim
« Last Edit: September 17, 2017, 08:24:13 PM by tpb03 »
Logged

tarahall

  • SSGuitar Regular
  • ***
  • Chip Points: 1
  • Posts: 20
    • View Profile
Re: EBay TDA2050 boards
« Reply #3 on: September 19, 2017, 08:39:21 PM »

That said, it *should* work like a plain TDA2050 single supply datasheet example, so "just trust the datashet, not the seller".

The data sheet clearly states that the TDA2050 is a 35W IC so the seller claim of 120w is obviously seller promo "BS".

« Last Edit: September 19, 2017, 08:42:30 PM by tarahall »
Logged
Pages: [1]   Go Up
 

* User Controls
 
 
Welcome, Guest. Please login or register.
Did you miss your activation email?
* Recent Posts
LM 3886 current feedback poweramp by tarahall
[Today at 07:37:00 AM]


EBay TDA2050 boards by tarahall
[September 19, 2017, 08:39:21 PM]


Need help with ROG: fetzer valve (gain stage) + buffer by tpb03
[September 19, 2017, 02:03:31 AM]


fender bassbreaker 45 by J M Fahey
[September 16, 2017, 03:27:00 PM]


Vintage Roland Cube-60 Reverb by Jazz P Bass
[September 15, 2017, 10:53:49 PM]

* Sponsors