Solid State Guitar Amp Forum | DIY Guitar Amplifiers

Please login or register.

Login with username, password and session length
Advanced search  

News:

SSGuitar has moved to PHP 7.1, enjoy the speed!

collapse
Pages: 1 2 3 [4]   Go Down

Author Topic: Fried Ampeg SVT-200T  (Read 14121 times)

phatt

  • Legendary
  • ******
  • Chip Points: 220
  • Posts: 1915
    • View Profile
Re: Fried Ampeg SVT-200T
« Reply #45 on: November 01, 2018, 07:53:18 AM »

Try plugging the guitar into the *Effects Return* if the crackle stops and the signal sounds clear then the Gain pot is likely stuffed.
You will have a bit less volume but the rest of the front panel controls should all function normally.

A common issue is FX loop switches.
The switch is built into the socket and with older gear that contact corrodes and fails to pass signal.

The schematic that *g1* kindly posted shows 2 fail points, the FX loop and there is also the *Line in/Line out* which is the same setup.

If you suspect fx loop problems then use 2 short patch cables and bridge those 2 loops if the amp then works fine you likely have an easy fix.
Phil.
Logged

Enzo

  • Legendary
  • ******
  • Chip Points: 183
  • Posts: 1810
    • View Profile
Re: Fried Ampeg SVT-200T
« Reply #46 on: November 01, 2018, 09:44:45 AM »

And really, it would be so much better to start a new thread for your amp instead of adding on the end of a thread that has been dead for five years.
Logged

Used.Benz.Parts

  • Chipper
  • *
  • Chip Points: 0
  • Posts: 3
    • View Profile
Re: Fried Ampeg SVT-200T
« Reply #47 on: November 02, 2018, 07:56:50 AM »

Wow! Thanks for the quick replies!

Phil, I’ll try your suggestion when I get a chance in the next few days.

Enzo, you’re right, a new thread would have been a better idea (given how old this one is). But I’ve found so little info on this amp, I was trying to write to people well versed in it and get their attention.

I’m any case, I’ll post results once I get it tested and we’ll go from there.

Thanks,
Dave
Logged

Used.Benz.Parts

  • Chipper
  • *
  • Chip Points: 0
  • Posts: 3
    • View Profile
Re: Fried Ampeg SVT-200T
« Reply #48 on: November 08, 2018, 03:25:44 PM »

Well, plugging into the FX loop had the same effect: crackling and popping until it just stopped. Nothing from the speaker after that. Except for a quiet hum - but you’ve gotta put your ear about 2-3 inches from the grille.

I’ve got the case open, amp sitting on a plastic crate. A closer look showed that there are globs of solder at 3 different resistors and 2 pair of the resistors are in parallel ...pretty sure they aren’t supposed to be that way because of the equivalent resistance and the solder is on the wrong side of the PCB [see pics, if they attach]. Also, are the transistors supposed to have screws through them? [Phillips heads, last pic.] I installed the one with the larger washer on it because it was either missing, or shouldn’t be there.

If I understand correctly, the corrosion failure in the FX loop switches MAY be contributing to this issue. If so, cleaning the corrosion off should allow a signal to pass through them. Yes?

I’m assuming that they were right on the verge of not passing a signal and by inserting the cable, the contact area may now be fouled completely.

—> I’ll get that board out and try to clean them as best I can. Granted I’m assuming a few things, and we all know what happens when assumptions are made, but it’s one place to start.

More details as it evolves.

Thanks!
Logged

phatt

  • Legendary
  • ******
  • Chip Points: 220
  • Posts: 1915
    • View Profile
Re: Fried Ampeg SVT-200T
« Reply #49 on: November 09, 2018, 06:38:22 AM »


YES, If the contacts in those switching sockets are dirty it WILL cause crackling. 8|

You need to bridge *BOTH*,, cable from *FX loop out to FX loop in*,,,
as well as another cable from *Line out to line in*.
Both could be faulty.

The switch is on the *return* and *line in* sockets only so get some electrical cleaner spray and give them a good blast, Also you may want to slide the plug in and out a few times to get contact again. if it's crackling try gently wiggling and reinserting the plug,, see if you can get the signal to play clean.

If you have access to those sockets you can bridge the terminals right on the sockets.

Regards those extra resistors soldered on the top side;
Someone has modified the circuit it's often easier to add a new value to the top side,, saves pulling the whole amp apart you just add the mod on top,, no big deal and I doubt it would cause the problem you describe.
You need to establish that those 2 loop switches are working or not FIRST,,, then you move on to other things.
Those 2 TO220 transistors don't need the screws.
Phil.
Logged
Pages: 1 2 3 [4]   Go Up
 

* User Controls
 
 
Welcome, Guest. Please login or register.
Did you miss your activation email?
* Recent Posts
kustom KAA-65 service manual by Jazz P Bass
[Today at 08:08:59 AM]


Marshall 3005/Lead 12 Power Trans Question by phatt
[November 17, 2018, 01:48:36 AM]


Roland JC-120: no effects working, any tips? by phatt
[November 17, 2018, 01:42:11 AM]


Sunn Beta Lead Input Switching Issues by edvard
[November 16, 2018, 12:59:21 AM]


Hybrid valve and TPA311x by jfetter
[November 15, 2018, 07:52:42 PM]

* Sponsors