Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Jazz P Bass

Pages: [1] 2 3 ... 14
1
Schematics and Layouts / Re: Scholz UDG Schematic
« on: July 01, 2020, 01:26:08 AM »
Nope.
Pretty rare pedal.
They only made about 100 or so.

2
Schematics and Layouts / Re: Kustom amp schematic
« on: July 01, 2020, 01:24:13 AM »
Call Kustom & ask for a schematic.
https://kustom.com/contact-us/

3
Pin 1 & 8 of the LM386 set the gain.
You are supposed to use an e cap (10uf) for more gain.
Not a jumper wire.
No cap and the gain is set to 20.

4
You will have to install something to limit the gain.
Some of the Zoom patches are off the wall high gain.
I have often wondered why they chose to do this.
You go from one one patch to the next one in line and the gain is off the charts.

5
Amplifier Discussion / Re: Rocktron Rampage R80
« on: June 25, 2020, 01:19:50 AM »
Or, if the FX loop is not being used, you can simply leave a patch cord installed.

6
Amplifier Discussion / Re: Rocktron Rampage R80
« on: June 22, 2020, 02:39:19 PM »
I would run a patch cord from the FX Send jack to the FX Return jack.
The Return jack has Normally Closed contacts that if they get dirty will prevent the signal from passing through to the power amp.
As to a schematic. Have you tried contacting Rocktron? techsupport@rocktron.com

7
Amplifier Discussion / Re: Inkjet printed circuit boards
« on: June 07, 2020, 07:59:22 AM »
Nice.
That may be the answer to the Roland EP-7 ribbon cable failure fiasco.

8
The Newcomer's Forum / Re: Newb here. I want to build an amp
« on: May 11, 2020, 09:00:12 AM »
There are a ton of prebuilt low power amps on E bay.
Search TDA2030 amplifier.

Keep in mind that the TDA2030 has been out of manufacture for a number of years.
The items currently on the market are knockoffs.

9
Amplifier Discussion / Re: Woodstock GX-55R SS Amp
« on: May 01, 2020, 01:14:59 AM »
5 pin Mosfet???
Sanken made 5 pin darlington output transistors.
The one that comes to mind is SAP09.
There also was a 15.

10
"Tube Logic – a marriage of solid-state analog technology and DSP"

Not too sure how the schematic will reveal the true nature.

11
I am no expert on the LM386D amplifier IC but it seems to me that adding a 'tone control' circuit on the output of the device is not a good idea.
Have you tried the circuit on the input side?

12
Some type of schematic of what you have tried would be a help.
The tone control is only 5 components.

You can even 'build' it on to a control pot.
http://beavisaudio.com/techpages/BigMuffToneControl/

Here is the schematic of the actual Big Muff TC:

13
Amplifier Discussion / Re: Ampeg Vh140c power transformer replacement
« on: April 01, 2020, 01:32:25 AM »
The transformer in the schematic specifically states "Export Model".
That is not what the OP has.

14
Tubes and Hybrids / Re: Mesa Triple Rec Woes
« on: March 17, 2020, 12:04:32 AM »
Here is the schematic

15
Schematics and Layouts / Re: JC 120 schematic
« on: March 04, 2020, 01:27:16 AM »
Try this:

Pages: [1] 2 3 ... 14