Solid State Guitar Amp Forum | DIY Guitar Amplifiers

Please login or register.

Login with username, password and session length
Advanced search  


SSGuitar has been upgraded to SMF v2.0.14 and PHP7!


Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - ENGR BUGO aka DimebuGG

Pages: [1]
Preamps and Effects / Re: Morley Classic Wah Qestions
« on: December 06, 2011, 12:47:13 PM »
Clean or wipe off dust in the LDR and LED. Adjust their positions to your liking (i.e. what you think sounds good in your ears).

Schematics and Layouts / Re: Randall RG100 hybrid
« on: October 13, 2011, 05:35:26 AM »
"100n C" = 100n Multilayer Ceramic Capacitor

Schematics and Layouts / Re: Randall RG100 hybrid
« on: October 12, 2011, 02:32:06 PM »
Thank you so much! Do you have it up and running? How does it sound?
Sounds like a Mesa..:)..just kidding. You'll never now if you won't try, buddy. Haven't build it yet but I'm pretty sure that thing will work.

Schematics and Layouts / Randall RG100 hybrid
« on: October 12, 2011, 12:37:45 PM »
This is my take on the Randall RG-100ES amp minus the original poweramp and reverb section - not to make it as complicated as hell for some beginners. For simplicity, poweramp is a TDA7293 based from Rod Elliot's application. Reverb section based from BELTON reverb brick.

Few notes:

1. In the reverb buffer section(starting from the 82n capacitor), I just directly input values from the Rebote 2.5 delay as this was originaly my plan to put a delay instead of a reverb. Feel free to experiment on the values of each resistors and capacitors or better yet use the values recommended according to the datasheet of Belton Reverb Brick.

2. Transformer is of course, as seen on the attached file, 25-0-25 / 3A to 4A.

3. 50K trimmers(0.5W) are used instead of fix 33K resistor(can be also used either) to adjust the correct Drain voltages of each FET according to the schematic or for your own tuning.

4. I didn't provide pads for the channel switching( just refer to schematic, it's very simple).

Comments, suggestions, and (violent) reactions are welcome.  :)
Enjoy!. ;)

Preamps and Effects / Re: Randall RG80/RG100 Preamp DIY
« on: October 11, 2011, 04:15:48 PM »
I'll post maybe tomorrow my recently finished layout of this RG-100ES amp project files. Actually, a mix of RG-100ES preamp(green and red channels), Belton BTDR reverb, TDA7293 power amp, and power supply.

Amplifier Discussion / Re: Elliot Sound Products Project P27A/27B
« on: February 23, 2009, 06:16:34 AM »
I think the diodes are there to create an overdrive especially at high volumes. Yes it does. I think Rod was just lazy to create two channels and it is clearly stated that if a fuzz or overdrive is not needed, those clipping diodes can be omitted.

Amplifier Discussion / Re: LM386 based guitar amp
« on: July 26, 2008, 07:26:37 PM »

Can you post the circuits/schematics of these please?

Regards Tony

choose "Guitar-mycro"..

Amplifier Discussion / Re: LM386 based guitar amp
« on: July 26, 2008, 07:22:51 AM »
And here it is, my cloned version of Nobels Guitar-Mycro headphone amp(just the stock). Damn!!!! This thing is so sweet better than Ruby or the Little Gem, IMO. The NORMAL mode is so crystal clear, damn I love it!! OVERDRIVE and DISTORTION mode also kicks ass!!!

Amplifier Discussion / Re: Gonna build a 100watt amp.
« on: July 18, 2008, 12:11:14 AM »

Oops sorry. my bad..i didn't notice the leftmost 22K resistor. :) :)..

Amplifier Discussion / Re: Gonna build a 100watt amp.
« on: July 17, 2008, 12:10:29 PM »
Hi JM,

I'm going to make sure to you that there's no mistake on that one. I guess your right, that 4,700uF cap is rated only at 50V and my transformer is at 6A, 35-0-35 sec. The rectified voltage was at +/-43V as far as I can remember. Maybe I'll try what you have said though.

So did I take your mod correctly like this?:

Amplifier Discussion / Re: Gonna build a 100watt amp.
« on: July 15, 2008, 10:24:22 AM »
ok, i've tried the "cheap 100W to 150W amp". It works fine but after a few weeks, filter caps in the PS suddenly begins to SMOKE!!!!!neither it blows but then I stopped using it..

And the rod elliot design is the one i'm using for 7mos. now...

Amplifier Discussion / Re: LM386 based guitar amp
« on: July 15, 2008, 09:39:20 AM »
This a Nobels Bass mycro I cloned for my brother

I also build the Nobels guitar micro where i put a cab sim on it..haven't taken a photo yet

Pages: [1]
* User Controls
Welcome, Guest. Please login or register.
Did you miss your activation email?
* Recent Posts
Early 70's Sears amp Finally found! My very first guitar amp! by galaxiex
[October 20, 2017, 02:24:55 PM]

Marshall 3005/Lead 12 Power Trans Question by J M Fahey
[October 20, 2017, 03:21:23 AM]

HH MA150 blowing mains fuses by Melv1
[October 19, 2017, 08:44:09 AM]

Hohner/Teisco frankenampmonster by galaxiex
[October 18, 2017, 04:18:49 PM]

Valvestate 8080 Woes by tubescreamer
[October 18, 2017, 09:44:32 AM]

* Sponsors