collapse

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Steve Conner

Pages: [1]
1
Tubes and Hybrids / LND150 tube emulator attempt.
« on: February 04, 2011, 10:34:33 AM »
OK, so following the recent discusion on FET-based tube emulators, I did some more work on my own ideas. Friday afternoon at work, and all that.  ::)

First I took the dual gate MOSFET cascode one and compared it against a Mullard ECC83. After some playing with the component values, they gave similar traces, but it was extremely temperature-sensitive. Someone had borrowed the heat gun, but there was no need for it: even breathing on the MOSFET caused about 10V shift in drain voltage. That made me think that the variation between different MOSFETs would be even worse.

So, I tried the LND150 in a circuit somewhere between the Trioderizer and the scalable diode. It worked surprisingly well. The clipped waveforms were as good, if not better than the dual gate circuit, and temperature stability seemed much better. Also, the component count is lower.

The major drawback is that it leaks DC out of its "grid". In conjunction with the usual 1M grid-leak resistor found in a tube circuit (well, 910k, as I ran out of 1Ms) this creates the positive voltage needed for the LND150 to have the right bias point. But tube circuits often use a volume control, or a different value to 1M, as the grid leak.

So, I'm working on that one. For now, this circuit would only be usable in a design that took the DC into account: it might not work if you just plugged it into a tube socket.

The scope shots show the LND150 circuit working alongside the Mullard ECC83, also set up with a 100k plate and 1.5k cathode resistor. Both are running off the same 250V supply. Top trace is the input signal, and the bottom two are the outputs from the ECC83 and LND150. I will leave you all to figure out which is which. :)

To paraphrase the Monty Python sketch, "Bring out your FETs!"

2
Tubes and Hybrids / My new hybrid- demo and schematic
« on: January 29, 2011, 10:17:28 AM »
Hey all

I normally hang out on the MEF, but I thought I would cross-post this here. I've been building amps for years, and the whole time have struggled with the questions: Is there really anything bad about transistors? Is it possible to make a good sounding hybrid? Well, after all those years of experimenting, here is my answer.

http://scopeboy.com/scopeblog/?page_id=96 - full story behind the project

http://www.youtube.com/v/DZigVupYve4 - demo video

http://scopeboy.com/scopeblog/wp-content/uploads/2010/12/ninja-corvette-demo-hq.mp3 - better quality version of video soundtrack

http://scopeboy.com/scopeblog/wp-content/uploads/2010/12/NinjaCorvetteHybrid.pdf - schematic

I'm working on getting rid of the remaining tubes.  :trouble

I was partly inspired by RG Keen's guide to the old Thomas Vox SS amps. If you squint at my output stage in the right light, it looks like an old Thomas Vox or Leslie, except with current limiting and a proper bias scheme. And I probably got some ideas from Teemu Kyttala's book, too.

Pages: [1]

* User Controls

 
 
Welcome, Guest. Please login or register.
Did you miss your activation email?

* Recent Posts

Z-MATCHER 100W IMPEDANCE MATCHER by Loudthud
[September 16, 2019, 04:42:44 PM]


Hybrid valve and TPA311x by jfetter
[September 13, 2019, 03:29:50 PM]


Marshall 5010 Needs Help by Jazz P Bass
[September 13, 2019, 12:12:27 AM]


Do you need a low pass filter in your amp when you already have the eq? by slimjohnny
[September 11, 2019, 06:01:57 AM]


Gallien Kruger GT200 by mandu
[September 10, 2019, 06:31:10 AM]

* Sponsors