1
Preamps and Effects / Re: Chorus Pedal Help
« on: June 30, 2018, 06:08:45 PM »
It’s a Digitech Hardwire...
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Preamps and Effects / Chorus Pedal Help
« on: June 27, 2018, 09:37:14 AM »
I have a chorus Pedal that I’m looking at and I need to repair it so a 9 volt battery will work in it...
It will work with a 9 volt power supply plug- in but NOT with a battery
I’m a newbie at this
Thanks for your help.....
It will work with a 9 volt power supply plug- in but NOT with a battery
I’m a newbie at this
Thanks for your help.....
3
Preamps and Effects / DOD 490 Phasor Pedal Schematic
« on: June 26, 2018, 09:33:27 AM »
Hi Again
I am looking for a DOD 490 Phasor Pedal schematic
I have looked at all the layouts on this sight
Any help would be appreciated....
Thanks <3
I am looking for a DOD 490 Phasor Pedal schematic
I have looked at all the layouts on this sight
Any help would be appreciated....
Thanks <3
4
Amplifier Discussion / Rocktron Rampage R80
« on: June 26, 2018, 08:51:49 AM »
Glad I am back
Hope to get feedback or help on my newest project..
I have a Rocktron Rampage R80 amplifier that I bought for 10.00 and was hoping to get it operational..
It has no sound coming from it and their is no burnt spots or trouble that I can see...
As I was going through it and using a chopstick to lift and touch components, I tapped on one of the 5 watt sandblock resistors and got a sudden sound and then moving over to the 3300 25 v caps and the sound came on for a while with everything working...
Then the sound went off and I have since replaced the 3300 caps and now I have nothing... This amp is so clean and I don’t not see any dead solder joints or any other problems...
I’m asking for the schematic or so help her to figure out the problem
I will try the FX loop shortly to see if I can get sound with that area
Thanks
Hope to get feedback or help on my newest project..
I have a Rocktron Rampage R80 amplifier that I bought for 10.00 and was hoping to get it operational..
It has no sound coming from it and their is no burnt spots or trouble that I can see...
As I was going through it and using a chopstick to lift and touch components, I tapped on one of the 5 watt sandblock resistors and got a sudden sound and then moving over to the 3300 25 v caps and the sound came on for a while with everything working...
Then the sound went off and I have since replaced the 3300 caps and now I have nothing... This amp is so clean and I don’t not see any dead solder joints or any other problems...
I’m asking for the schematic or so help her to figure out the problem
I will try the FX loop shortly to see if I can get sound with that area
Thanks
5
Amplifier Discussion / Fender Stage 100 Noise
« on: April 29, 2015, 08:12:52 AM »
Good day
Just wondering if anyone can answer the question about Fender Amps and why they HISS so much?
I know this about Fender amps but was just curious about this
I bought ( 50.00 ) this amp off CL and it works perfect
Any way to subdoo this problem???
Just wondering if anyone can answer the question about Fender Amps and why they HISS so much?
I know this about Fender amps but was just curious about this
I bought ( 50.00 ) this amp off CL and it works perfect
Any way to subdoo this problem???
6
Amplifier Discussion / Randall Commander 120/212 Amplifier
« on: December 08, 2014, 04:46:01 PM »
Was wondering if anyone has a website to look for a 1976-77
Randall Commander 120/212 amplifier replacement knobs
These have the " R " in the center of a black and silver skirted knob
Thanks!!!!
Randall Commander 120/212 amplifier replacement knobs
These have the " R " in the center of a black and silver skirted knob
Thanks!!!!
7
Tubes and Hybrids / Re: Traynor YCV 40 Tube Amp Problems
« on: September 15, 2014, 01:11:51 PM »
Thanks G1 for feedback
After reading about these amps, there was a problem with the standby
switch causing these kinda problems
A friend and I put his Traynor tubes in my amp and it came to life
Sounds good.... Probably stay with the SOVTEK tubes in the power side
And run electro harmonix in the pre-amp side
Thanks again
After reading about these amps, there was a problem with the standby
switch causing these kinda problems
A friend and I put his Traynor tubes in my amp and it came to life
Sounds good.... Probably stay with the SOVTEK tubes in the power side
And run electro harmonix in the pre-amp side
Thanks again
8
Tubes and Hybrids / Traynor YCV 40 Tube Amp Problems
« on: September 02, 2014, 09:41:41 PM »
My Traynor YCV 40 Amp is having problems with the volume
On low volume of 2 to 4 it sounds fuzzy and distorted
As I turn up the volume, it gets worse with this problem
After reading about these amps, it seems to be a problem with the standby button
If anyone has experienced this, please let me know
Possible tube replacement is in order after turning it on and letting it sit and then looking at it in the dark for tube glow
The tubes were cold a minute or less after shutdown and if I am not mistaken, one tube not even working
On low volume of 2 to 4 it sounds fuzzy and distorted
As I turn up the volume, it gets worse with this problem
After reading about these amps, it seems to be a problem with the standby button
If anyone has experienced this, please let me know
Possible tube replacement is in order after turning it on and letting it sit and then looking at it in the dark for tube glow
The tubes were cold a minute or less after shutdown and if I am not mistaken, one tube not even working
9
Amplifier Discussion / Re: Can anyone identify this Amp?
« on: July 03, 2014, 08:06:33 PM »
To reply to this post... I would like to say that the HH Speakers were used in the Laney Series Amps
I have a Laney GC60 A and a Laney GC60 C
Thanks
I have a Laney GC60 A and a Laney GC60 C
Thanks
Pages: [1]