Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sweetspence

Pages: [1] 2
1
Tubes and Hybrids / Re: starved plate design
« on: September 03, 2012, 12:28:47 AM »
 mozwell, you are the man!!  i almost gave up on trying to mess with this thing. Many thanks
 :dbtu:

2
Tubes and Hybrids / Re: starved plate design
« on: June 04, 2012, 08:49:34 PM »
I got this thing for free so i looked it up and it got some good reviews most people only complained about the tubes in it (others just the brand) but over all i figured it wouldnt be a terrible thing to have around. will let you know how it sounds when hooked up. Many thanks

3
Tubes and Hybrids / Re: starved plate design
« on: June 03, 2012, 07:20:23 PM »
so if i were to do something like this how complicated would it be in my berhinger tube composer where the tubes are just used as coloration in the circuit?

4
Tubes and Hybrids / starved plate design
« on: June 03, 2012, 05:21:46 PM »
heres a question and it might have been answered somewhere before but here it is. if you have gear that runs on a starved plate design is there a way to up the plate voltage and truly have a tube in the signal path? what would be the problems with this modification? any thoughts are greatly appreciated

5
Amplifier Discussion / Re: headphone jack feeds back?
« on: February 05, 2012, 09:40:59 PM »
yeah its odd to say the least.. i will do some tinkering to see if i can isolate the issue. on a good note this thing actually has some legit tones some of the emulations are so close its unreal. :duh

6
Amplifier Discussion / Re: headphone jack feeds back?
« on: February 02, 2012, 11:27:11 PM »
heres the amp "phones" jack above guitar input..
http://www.behringer.com/EN/Products/LX112.aspx

7
Amplifier Discussion / Re: headphone jack feeds back?
« on: February 01, 2012, 11:27:15 PM »
headphones are using a 1/8" to 1/4" stereo adapter and it feeds back into the main speaker and not the headphones. no controls have any affect on the feedback.

8
Amplifier Discussion / headphone jack feeds back?
« on: January 29, 2012, 02:23:25 PM »
i reciently bought a behringer vampire 112 modeling am and every thing worked great untill i tried to plug in headphones... so guitar it plugged in and volume is off i plug in my sennheiser headphone and the thing starts feeding back, everything goes back to normal when i unplug headphones. could it be leads are touching? or some sort of ground loop?

9
Preamps and Effects / Re: distortion with lots o sustain?
« on: November 24, 2011, 01:43:50 AM »
sorry should have specified. its a crate mx10 and its just sorta lifeless i understand its the nature of cheap practice amps but it will have to do till i build my dream amp <3). so is there some sort of od/dist that might help remedy my problem some?

10
Preamps and Effects / distortion with lots o sustain?
« on: November 23, 2011, 12:24:19 AM »
my amp is quite dead in the terms of reverb and sustain can i solve this with an od/dist pedal?

11
Amplifier Discussion / discrete poweramp
« on: November 23, 2011, 12:21:40 AM »
any resources on this?

12
Preamps and Effects / Re: digitech rp250 power supply
« on: October 09, 2011, 10:07:39 PM »
correction 9V ac-- sorry

13
Preamps and Effects / Re: digitech rp250 power supply
« on: October 09, 2011, 12:43:00 AM »
so the ac power supply i found is dead... now the unit wants 12v ac so i assume it converts it to dc internally but can you use a dc input or would this not work due to the circuitry already in place?

14
Preamps and Effects / Re: digitech rp250 power supply
« on: May 17, 2011, 05:02:08 AM »
no it is ac, its retarded i know..... anyways yeah i found a wall wart at the goodwill and was overjoyed to make use of my $200 paperweight. i just wanted to double check and make sure i didnt fry the thing and have it remain and oversized paperweight lol
 ;D

15
Preamps and Effects / digitech rp250 power supply
« on: May 16, 2011, 08:09:50 PM »
I lost my psi and have been trying to find a replacement now the pedal requires 9vac 1.3 amps my question is how picky is a pedal like this? I have a psu that gives1.5 amps will it harm the pedal at all? Thanks

Pages: [1] 2