You could check if the headphone out still gives a good signal, you at least know if the problem is in the power amp or not.

I like Tech 21 stuff, but I don't see why you'd want this for guitar. Any kind of overdrive/distortion you might get out of it would be pretty basic. You'd need to park a distortion pedal or multi-effects box in front of it to get any kind of versatility out of it.

No matter what, you should not buy this without demoing it first.

Quote from: Enzo on May 11, 2009, 09:44:14 PM
All the TIPs will have the same pinout.

Did you leave out the mica insulator under any of them?  Go down the row of power transistors and see if the tab is shorted to the heat sink.

I didn't see any mica insulator. I thought it was just thermal paste between the transistors and the heat sink, so that's all I used. If they're not allowed to be touching that could definitely be the problem. The replacement transistors are all metal on the back.

Several months ago it died. I opened it up and found a single fried resistor and a one or two bad solder joints. I re-did the replaced the resistor and re-did the joints. This worked fine for a while, but it wasn't completely reliable. I sometimes had to smack the amp to get it to make sound. Some time later it stopped making sound altogether. I opened it up to see if I could see what was wrong. I didn't see anything, and tried playing opened up. This was a stupid move because the power amp transistors where off their heat sink. I realized this when I saw one of them smoking. Later I noticed that the speaker had become disconnected. I reconnected the speaker and I think fed it DC current when I turned the amp on. Just yesterday, I replaced all the power transistors. At first, it powered up and made almost no noise, but the fuse blew after about a minute. Subsequent fuses blew within second.

There are many things that could be wrong. I was wondering if the pinout on one TIP147 could possibly be different than the pinout of another TIP147 by a different manufacturer. I could've connected something wrong. I might have damaged the new transistors or the board itself beyond repair with my weak soldering skills. I really don't know.

Whatever the case I really do want to build my own amp. I also have a dead Line 6 Spider II HD 150 that I bought to replace the Fender. 

The sensitivity of guitar speakers typically blows away that of other types of speakers at the expense of accuracy. If a home audio speaker can handle 100 watts from your home stereo, it can handle 100 watts from your guitar amp. It just won't be as loud, and might not sound "right". If you hook up a guitar speaker to a home stereo, the music will sound awful.

Some speakers are rated at the power where they cross a certain distortion threshold even though they're capable of handling much more power before taking on damage. I've seen this with car subwoofers.

Anyway, as long as the speakers can handle the power and the amp can handle the impedance, nothing terrible will happen if you hook them up.

The schematic for the old amp is here in pdf.

I've had this amp for 12 years and it's been good until recently. I never cared for the drive channel, but the clean was very nice. Anyway, it's been giving me a hard time. I just replaced all 6 power transistors. I knew at least one of them was bad. Now it blows the fuse. I'm guessing I did something wrong, but I don't know what, and I don't really feel like trying to figure it out as I think I may have damaged the board itself. After coming across this site, I'm starting to think it may be time to scrap the board and try to re-use the larger components to build something new.

The amp is rated at 105w into 8ohm and 160w into 4ohm, so I'm looking to build a power amp that will match or nearly match that output reusing the old power transformer. According to the schematic, the power supply puts out +/- 45vdc and +/- 16vdc. I'm very noob with this stuff, so I don't what would work well with that, besides the old power amp, which uses 3 TIP142 and 3 TIP147.