Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Topics - Hawk

#1
Vibrato not working..can hear a very feint ticking sound. Suggestions?

Sent from my XT1635-02 using Tapatalk

#2
Tubes and Hybrids / Gibson Maestro Reverb Issue
May 08, 2018, 10:34:37 AM
Reverb is very weak or non-existent, hard to tell. Cable checks out. Amp works otherwise....Reverb pot has none or very little effect...reverb pot checks out okayhttp://cloud.tapatalk.com/s/5af1b3de20ea5/ga1rt%20%281%29.pdf

Sent from my XT1635-02 using Tapatalk

#3
Looking to change caps but not 100% sure how to identify. See pic....the large black Sprague caps have a red ring on them but I don't think they are polarized. The smaller black caps--how to identify? One of the caps tells us it is .03 ohms. Under the resistors there are 4 caps that have been flattened... can't read them--coupling caps? Guess I'll have to remove resistors to get at these caps. Thanks!http://cloud.tapatalk.com/s/5aeca230849eb/gibson-ga-1rvt-amplifier-schematic.pdf

Sent from my XT1635-02 using Tapatalk

#4
Amplifier Discussion / Astron Duplex Multi-Cap
April 29, 2018, 05:34:01 PM
I might need to replace a multi cap--Astron Duplex multi-cap on a Gibson Maestro Reverb Echo amp. Haven't tested it yet but I want to understand how it works before I check it out.  On the side of the cap is says that the black wire is common. The other wires are for 20,10, and 10 ufd. Is the black wire the common ground wire for all three caps and does it tie the negative ends of all the caps to ground? Are the other wires the positive ends of the 20,10 and 10 caps and got to circuit? Thanks
#5
I'm troubleshooting a Gibson Maestro Reverb Echo amp and wondering if anyone knows the impedance of the 8 inch speaker? It shows a very low resistance reading .7 ohms so I know it's done.
Thanks.
#6
Hi!

Well, no matter what channel I use in this amp, if I crank the bass on any channel the amp modulates on and off rapidly. I can crank the amp without bass and all sounds good but once I dial the bass in in there is a big modulating problem--like a loud bap,bap, bap sound that continues for quite some time until the sound dies out.  Power supply unable to keep up with low frequencies? Any thoughts? I replaced the output IC but same problem....anyone experienced this before? Suggestions? Thanks.

I also ran the amp through another speaker and the same problem exists.

Also hear clicking sound from power amp when this happens--relay?
#7
Hello Folks,

This amp sounds great, except in the last 30 minutes it's made two high-pitched squealing sounds which sound like sirens. This siren-like sound last for 1-2 seconds then stops. Thoughts? Cap issue (s)?

Thanks.
#8
Amplifier Discussion / Peavey Renown
June 26, 2015, 09:12:28 AM
Trying to repair an amp for a friend. Keeps blowing fuses. Drawing over 5 A current rating at 40v, not good. Check PT and found .3 ohms from Red/Centertap, both sides. Other fuses on lower voltage are fine. Need to pull board to check diodes--one half of their legs are under the board. Caps show good on ESR meter.

Did the lightbulb test on the PT, RG Keen's method, and no light at all...hmmm, internal short? Any other tests just to make sure?

I've included the schem and a pic of the output transistors. Always felt intimidated by these output transistors. Do I need to take out the pcb to check them?  :-[
#9
Hi,

So I thought I had a microphonic power tube next to the phase inverter--it squealed if moved slightly in its socket but not always and then it would sometimes squeal on its own but not always. I swapped tubes to see if that made a difference and when I turned the amp back on that tube blew in the suspect socket and now none of them work (fuse is still good and amp turns on). The tube may not have been sitting in properly as  the tube holder was a little loose. I had cleaned the tube socket earlier with De-Oxit and let it dry for a good half hour to remove any gunk from the tube socket.

These amps are a pain to take apart but I'm wondering 1. Loose solder joints?  Or 2. Can a tube that doesn't sit tightly in its socket cause arcing and possibly create a microphonic situation?

The tube  furthest away from the phase inverter seemed a little microphonic when I moved it a little as well. But I can't test that now as these tubes are in series so no dice. I'll have to pick up some more tubes. I should probably check to make sure all voltages are correct as well.

Thoughts on how to proceed without  blowing more tubes and spending more money? :-\

Thanks,

Hawk
#10
Tubes and Hybrids / Capacitance Meter
June 03, 2015, 09:24:44 AM
I'm using a blue ESR meter for caps 1uf and above and I love this meter! But what about those little tiny caps? What are techs using to measure these little guys? Can anyone recommend a cap meter? I'm currently using a cheap Mastercraft Meter but I question the cap readings. I also know these little caps need to come out of the PCB in order to test properly. So, I'm putting it out there, what do people recommend? What works for you?

Thanks.
#11
Tubes and Hybrids / Amp Cradle
June 01, 2015, 02:19:51 PM
I've been putting off buying an amp cradle due to cost. Everyone using one? Or have you found a cheaper alternative to working on a tube amp chassis....thanks!
#12
Hello Folks!

I'm trying to replace a Power Transformer for a Peavey Classic 30, 120V operation , with a Peavey Universal Transformer. The original transf. had two yellow secondary wires that attached to a connector which slid over a set of two pins on the board. There were also two red secondary wires which went to another connector and that connector slid over the other two pins on the board. Easy stuff.

But the universal transformer in the attached pic has two yellow wires with separate connectors and two reds with separate connectors. I'm guessing I need to remove the connectors and solder each of the four wires to the pins. Makes sense?

Also, the tech notes that came with Peavey transformer tell me to connect both the blue and brown to the hot side of the supply and the blue  and white to the neutral side which, again, appears easy enough.

I've never used a universal transformer replacement so I'm a little confused on this one.
:-\
Thanks!
#13
From what I understand the EL84 output tube filaments in a classic 30 are wired in series so if one tube malfunctions then that stops the voltage going to the other tube filaments so the other tubes will also stop working. If that is true is there a way to wire the filaments in parallel? Or is that something we wouldn't want? Was the output section designed that way for a good reason?  Thanks.
#14
Amplifier Discussion / Thermostat/Fan
April 15, 2015, 10:35:00 AM
Hope this is okay to post as this is an audio amplifier rather than a guitar amplifier, but same concepts. I've attached a schematic (see bottom of schematic)

Trying to understand how the thermostat works. It is supposed to turn on the fan when the fan gets too hot. The fan is rated at 12V but the voltage on one side of the fan at R108 is 18v (won't that fry the 12v fan?).
What does this thermostat look like? Is it a thermistor?  I find no voltages on Q101,102. Is it safe to assume that there is no voltage as the thermistor is an open circuit until  the temp gets too high and therefore no voltage on transistors? Hmmmm...
Thanks! :-\


#15
Amplifier Discussion / Marshall Valvestate 8100
March 13, 2015, 01:53:11 PM
 Probably a simple fix but when I turn the effects knob (eff)  to the right the volume cuts out, starting at about 12 o'clock and then goes completey dead when turned all the way to the right. I used Deoxit and got rid of all the scratchiness but same problem. I removed the pot and measured 22K as it should be. As I turn the pot to the right it's as if the signal is being shorted to ground and then at the far right: dead, volume completely cuts out. ???
#16
Amplifier Discussion / SWR Studio 220 Capacitor Question
February 19, 2015, 08:41:01 PM
I've included two images. Amp belongs to a friend. There are three leads from the two caps on the board and only two are being used. To me this doesn't look like a dual cap, so I don't understand why there is an extra lead. It's not used in the amp and the amp works just fine. ??? Thanks!
#17
The notes on clean channel decay normally, but not on the distortion channel. Instead they sound for awhile then suddenly stop as if being sucked out of thin air. Something is damping the natural decay of the notes...any suggestions? Transistors? Caps?

Also, using my scope and a 1 KHZ signal injected, and the Distortion Signal selected, the signal is very distorted on the Scope. Of course to me that makes sense as this is distortion, but what kind of distorted signal should I be seeing on the Scope? There is nothing as readable as a sine wave with some distortion on the wave, or signs of saturation or cutoff, just a wierd distorted signal which looks the same at all volumes, just larger and smaller values of the originally crazy signal...does this have a lot to do with the first three lines of my query?  thanks for reading this!
#18
I've been reading Jack Darr's book, Electric Guitar Amplifier Handbook. I love  it!

1. He refers to hooking up an ammeter to the collector of the output transistor to measure current while slowly bringing up your variac and keeping an eye on the current (I'm pretending the amp is blowing fuses and trying to discover the problem). I chose to use the MG250DFX as my practice mule, so I can't physically unhook an output transistor collector and hook in my metere. Instead, I'm dealing with the TDA7294 DMOS audio amp. Do I break the wire connection to Pin 14 and hook in the ammeter there??? (This amp works so I'm just getting used to being hands on and am not trying to fix it, at least not this part--some quick dying of notes on distortion channel which I'll deal with later).

2. On the clean channel, I injected a 1 KHz, 50 mv signal into the amp. I hooked up a Weber VST Dummy Load on 8 ohm impedance. I hooked up an rms voltmeter across it. I turned up the master volume to full and slowly brought up the gain until the top of the wave started to flatten then pulled it back a little. At that point I found approx. 3.8 volts across the dummy load of 8 ohms. Using the formula, Esquared/8 I come up with 3.8x3.8/8=1.08 Watts. What does this reveal? It's obviously not the full output power of the amp.

Thanks!
#19
How does the DG212CJ function in the post secondary transformer set up? I've tested and found the 5V fed from the voltage regulator and also found +/-15V on the DG212CJ. I found 15V on pin 8 of the 4558DD Dual Op amps in the schematic above. Since I haven't looked under the board is it safe to say that pin 8 of one of the op amps is feeding the voltage to the DG212CJ?

I'm having a little trouble reading the schematic as I don't see where they would take off the 15 volts to feed the pre-amps section. Where does that usually happen?  Thanks, Hawk (the new guy!)
#20
Hello Everyone,

New to this forum. New to some aspects of guitar amps,or perhaps many!. Bought a Marshall MG250 and wanted to hook it up to my Weber Dummy Load Box, but I soon realized that there are two speaker outputs on back of amp, left and right, min 8ohms, 2 X 50w rms into 8 ohms. My first guess is that I need a second dummy load. I understand how parallel/series speaker hook ups work but not quite sure if I can hook up the speakers together and run a line into a quarter inch speaker cable into the dummy load. The speakers are 8 ohms each. Would they be hooked up internally in series, 16 ohms? If they were parallel they would be  4 ohms, yet the caution on the back is 8 min ohms. The two outputs have thrown me off! Can I somehow hook this amp into one dummy load? Thanks very much.