If the rectifier's are not in circuit then there would be no B+ vdc. So I can't immediately imagine the caps are the issue from that standpoint. Of course posting a schematic would be a good thing. It seems the transformer may have other windings -/+15v rails and your heater's winding. Try disconnecting all secondary connections when in doubt. Light bulb shining with secondary taps disconnected from circuit is not good. Right now from what you have written we need to clarify what you are describing and a schematic. We need voltage readings if the light bulb is not shining bright.

Hi friends; It's been a very long time away. A lot of things got put on hold including amp repairs. I have been working on a Peavey Ecoustic 112 amp lately. Everything is running smooth and quiet except the reverb which is important for the new owner. I have reverb when I turn the pot up but I also get like a 60hz hum. I tried re-soldering, cleaning the pot, switched out the tank with 2 diff ones but nothing quiets it down? Does anyone have a suggestion? Looking through the Peavey Forum I found evidence that Peavey amps are known for noisy reverbs. Someone on there suggested using an isolation transformer which I have not tried.

Thanks for all the info and hints. I'm about to order the parts that I don't have in my stash and as soon as they arrive, I'll start breadboarding. Provided nothing unexpected gets in the way, that is.
As far as the higher voltage goes, I happen to have an LT1054-based voltage doubler put together, so I'll give it a try at roughly 18V too.
Have a good one and stay tuned!
M

I'd try 10pF to 22pF, base to collector, similar to the trick employed to smooth down silicon transistors in fuzzes, but that's a matter of taste
I had a bit of downtime this arvo and threw the Vulcan on LtSpice: the frequency response is VERY similar to the Randall RG100Es, so you'll probably hot rodded marshall vibes. That doesnt mean that it will sound like a Randall, though: clipping thresholds and gain increments are very different.
I was also surprised to see that the circuit, as is, is already shaving off some dBs above 6kHz.
I'd be tempted to try it at higher voltages, with low hFE transistors, just for the sake of it.
Oh, and the diodes do mimic grid clipping: they chop almost half of the waveform before the gain stage. Very clever design with just a few parts

Thanks for the reply, Umlaut.
Looking at the schematic, I also expect it to sound like a Marshall on steroids. Like a DSL or a Bogner Ecstasy perhaps?
Speaking of snubber caps, do you mean in parallel with collector resistors?

Hi there!
I have this one on my to-breadboard along the line.
Seems to be marshall-voiced, judging by the filtering, and pretty high gain.
Might be wrong, but perhaps the diodes mimic grid saturation as in a valve amp.

Indeed breadboard first, especially if using other trannies, and check the voltages. Personally I'd try snubber caps on the last two gain stages.

Good luck!

I have a problem with a multi watt dual rectifier head.
It keeps blowing fuses and a rectifier tube.
Using the light bulb mains lead method, even with both rectifier tubes out of the unit and on standby it seems to be drawing quite a bit of current. No change with power tubes also removed.
Is this likely to be the large filter caps going or any other suggestions?
Thanks in advance

Hi, everyone, first build-related post of mine   
Soon, I'm going to build Joe Davisson's 4-stage Vulcan preamp using the schematic posted on his website and I have a few questions before I embark on this project.
1. Has anyone tried it?
2. If so, how does it sound? Judging by the number of gain stages, it's a hard rock / heavy metal machine.
3. I'm going to use BC337 transistors because I have a lot of them (not much of anything else tbh). Apart from pinout and biasing, is there anything I should specifically pay attention to?
I'm going to breadboard it first and, of course, I'll keep the forum updated on the progress. That, however, may take a while because adult life is the way it is
Stay tuned.

Thx G1!

Attached some screenshots just after the push-pull mimicker:

Nice work and great name for your project.