Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - saturated

#1
Man Joe is getting some really tempting reverb ads on here...must resist  :'(  :P

Anyhow I found that if you are playing a song off YouTube on your phone like trying to learn it while you play...if you hold it up to your pickups it will play through your amp

:P  :-[  :-[  8)
#2
The fret rest is awesome.  I always knew about them but told myself why do I need one I keep my guitars in cases.

So I bought one used local and it has been a lifesaver

You cannot view this attachment.

Yes i do love it so handy when setting up... plugging in..or if you need to set it down for a moment

You cannot view this attachment.

I missed out all these years not having one  :'(
#3
Yes sir Im not sure what V offset is  :'( but I think they meant compare the two voltages rather than just measure across A and B and turn the pot until it's zero.

At one time I was taking pics of the exercises in the textbook but got kinda wigged out about copyright issues.   :P
#4
I was gonna suggest perhaps C61 is shorted to ground but it says you already replaced it.

Maybe start probing around and try to find where that portion of the circuit has continuity to earth.

 :P

Anyway I'm out I shouldn't be "contributing" to these fix it threads  :P
#5
Today I had to make a parallel circuit with a variable resistor

You cannot view this attachment.

Then do some calculations etc for voltage drops and calculate how many ohms the variable resistor should be for Va to equal Vb

Then make the circuit and do it

You cannot view this attachment.


So yeah pretty boring but it's definitely helping I have to chug through this in order to get to the cool stuff.

Pretty funny the book noted "although Vo can be directly measured across A and B it is good practice to make all measurements with respect to ground"

 8)



#6
That looks fantastic  8)

You did an awesome job.

Congrats  8)
#7
I put all the knobs nuts washers etc back on my all time favorite amp

You cannot view this attachment.

They had been off since you guys fixed it.  I had planned to get around it but never did then I had an intermittent input jack and noticed how bad the chassis was rocking back and forth.

 8)
#8
Hang in there bud  8)

Don't give up before the miracle  :P

If anybody can get your amp running these guys can.

Maybe post up some pics of the boards

 :)
#9
Good afternoon solid state afficianados.

Hope your weekend is going well at least what's left of it.

:P

I had a question about preparing some banana jack patch cable connectors whether or not these needed to be soldered.

The wires shown are not gonna be used they are only to illustrate the routing of the holes in the metal part.


You cannot view this attachment.

Maybe I just strip the wire insert it and screw the cap down...idk

Thanks


#10
I'm relieved that my signal generator provided some nice traces

You cannot view this attachment.

You cannot view this attachment.

Idk why the trace from that transformer was so sketchy.


#11
Yes sir thank you  :P

I decided to take a look at this on my scope

Btw here is the source of 12v ac

You cannot view this attachment.

So connecting scope probes directly to cables coming from ac source

You cannot view this attachment.

My phone was struggling to get a full trace left to right despite trying to adjust trigger etc the trace was jittery and flickering real bad

So now connect scope probes to (+) and scope ground to (-)

You cannot view this attachment.

Which I like that but when I had the scope switched to ac I had just a flat line

Then connecting scope probe to (~)

You cannot view this attachment.

So I guess everything is cool. 

I'm off to connect some other stuff to the scope and try to get a better full steady trace.

 :P



#12
I decided to put a load on it...12k ohm resistor

Similar results

You cannot view this attachment.

More Bruce

 :P

I have a feeling Bruce says we need some capaci-taters
#13
Thank you sir I wanted to try and replicate this scenario so I did

I had a device with taps on the back for 12v ac so I rigged it up

You cannot view this attachment.


:P

You cannot view this attachment.

Results

You cannot view this attachment.

So...idk

I guess it's time to play some Bruce Hornsby

 :P

#14
Amplifier Discussion / Re: Jazz Chorus 60 repair
April 14, 2024, 01:45:56 PM
Wow nice amp  :)

Welcome to the forum

 8)
#15
Ok guys sorry for the bo bo  :'(

Anyhow removed the old one (no easy task) and got a new one in

You cannot view this attachment.

Seems all is good when measuring the (+) pin and two middle pins (~)

(+) pin reads about 40v DC (have no idea what it is supposed to be


You cannot view this attachment.

But when I read the middle pins I get like 16v ac but what the heck I get 20v DC

You cannot view this attachment.

I think I'll call it a night

 :P