Welcome to Solid State Guitar Amp Forum | DIY Guitar Amplifiers. Please login or sign up.

November 29, 2022, 07:32:20 PM

Login with username, password and session length

Recent Posts

 

Recent posts

#91
Schematics and Layouts / Re: Randall RF-1003 Footswitch...
Last post by joecool85 - September 27, 2022, 09:10:05 AM
I looked up the manual for this and found it is a two button switch on a TRS 1/4 cable.  This just means it uses a stereo 1/4" cable rather than standard mono guitar cable.  Testing will be the same way, but you will go from the ground at sleeve (ring closest to the wire) to the tip or to the middle ring.

https://www.randallamplifiers.com/wp-content/uploads/sites/9/2019/09/RG1003HMANUAL.pdf
#92
Schematics and Layouts / Re: Randall RF-1003 Footswitch...
Last post by Montywitha-Y - September 27, 2022, 12:46:31 AM
Thank you. I will test that as soon as I can. It is a 3 channel amp, so if there's any further technical info to make things work correctly to switch between the 3, I'd sure appreciate it. Like I said, I am new to these concepts and am looking for greater understanding. Thanks all!
#93
Schematics and Layouts / Re: Randall RF-1003 Footswitch...
Last post by joecool85 - September 26, 2022, 09:14:57 PM
Quote from: Montywitha-Y on September 26, 2022, 04:53:59 PMI'd like to start by thanking you all for having me in your forum! I'm new to both solid state amps and to electronics builds. I am wondering if anyone here has a schematic or wiring diagram (makes noob blood boil just slightly less) for the foot switch that works with the Randall RG1003H amp head. It seems I'm deeply allergic to the idea of paying $100 for this foot switch (when they can even be found). If not, I would humbly ask if an owner of that foot switch could take a good picture of the layout and post it? Anything would help. Thanks, again!

I haven't looked this one up, but most amps just simply short the tip and sleeve of a 1/4" cable for the switch.  To test this, plug in a guitar cable, and then use a wire (or other piece of metal) and short the tip and sleeve - see if it changes the channel on the amp - it probably will.  If so, you'll need to determine if it needs a momentary or standard switch.  If it switches channel when you connect the two leads, then changes back to the original channel when you disconnect, you need a standard switch.  If it stays switched until you touch the leads together again, you need a momentary switch.
#94
Schematics and Layouts / Randall RF-1003 Footswitch for...
Last post by Montywitha-Y - September 26, 2022, 04:53:59 PM
I'd like to start by thanking you all for having me in your forum! I'm new to both solid state amps and to electronics builds. I am wondering if anyone here has a schematic or wiring diagram (makes noob blood boil just slightly less) for the foot switch that works with the Randall RG1003H amp head. It seems I'm deeply allergic to the idea of paying $100 for this foot switch (when they can even be found). If not, I would humbly ask if an owner of that foot switch could take a good picture of the layout and post it? Anything would help. Thanks, again!
#95
Amplifier Discussion / Re: Fender 112 Deluxe Plus
Last post by FenderDeluxe112Plus - September 26, 2022, 03:12:56 PM
Thanks for your help Phil-  I will have another look at the power amp- will pull the heatsink diodes cr6-8, plus cr10/12 and check the electrolytic caps.
If anyone has any ideas about how to track this fault down, I would be glad to hear them. Thanks, Andy
#96
Amplifier Discussion / Re: Fender 112 Deluxe Plus
Last post by phatt - September 25, 2022, 10:37:51 PM
Then the most likely place is the power amp itself. You said in the first post you replaced the 4 power transistors.
Whatever caused them to fail may well have taken out other parts of the power stage.
We have been over the power amp before but maybe there is a need to look deeper into that. You will need better minds to establish just what has failed.

Phil
#97
Amplifier Discussion / Re: Fender 112 Deluxe Plus
Last post by FenderDeluxe112Plus - September 25, 2022, 11:10:25 AM
Ac across speaker leads 4.5vac
#98
Amplifier Discussion / Re: Fender 112 Deluxe Plus
Last post by FenderDeluxe112Plus - September 25, 2022, 11:05:47 AM
Tps 1-6 check out as per schematic

But excess ac still present on tp4
Ac on tp3 0.068
Ac on tp4 0.235




#99
Amplifier Discussion / Re: Fender 112 Deluxe Plus
Last post by FenderDeluxe112Plus - September 25, 2022, 10:47:01 AM
New main filter caps and psu diodes
Cr22- 25 replaced.
Buzz still there. 
#100
Amplifier Discussion / Re: I’ve Really, Really, Done ...
Last post by Tassieviking - September 20, 2022, 10:48:26 PM
If you want something that slips into that chassis, start looking around for another Peavey,
You like the sound of the amp so just get another one,

If you get the same amp you can start looking up some electronic lessons on the web, and then start taking measurements on both amps and slowly trace the fault yourself.
You might slowly learn more and more, get the amp fixed eventually.

I bet you would start building your own stomp boxes in no time.
I saw a Peavey Special 130 go for $65 at an auction where I live 2 weeks ago.
Keep looking till you find what you want.
Just don't throw it out, someone else would love to have a go at repairing it.